Power:
Speaker Volume:
Input:
Incoming Format:
?
Select between stereo and the available surround modes.

Audio Mode:
Output Format:
?
When headphones are enabled on the Line Outputs, choose whether audio outputs from just the speakers, speakers and headphones, or just headphones.

Output:
Headphone Volume:
Subwoofer Mute:

Speaker Volume Settings
?
Set the volume level the amp is set to when it is powered on.

On Speaker Volume:
?
Set highest volume level the amp can be turned up to.

Max Speaker Volume:
?
Select the default output level when speakers are selected on outputs 6-7.

Line Output Gain:

Headphone Volume Settings
On Headphone Volume:
Max Headphone Volume:
?
When headphones are enabled on the Line Outputs, choose whether the headphone output has independent volume control, or if the headphone output follows the main speaker volume.

Follow Speaker Volume:

Power Setting
?
Determine whether the Bijou turns on, goes into standby, or goes into the last state after a loss of power.

Power Recovery:

System Info
Serial Number:
MCU Firmware:
DSP Firmware:

X
X

FW Update:
Save Settings:
Load Settings:
System Reset:
?
When signal sense is active, select which input is automatically switched to when signal is detected on that channel. The Bijou will always switch to eARC when eARC signal is detected.

Priority Input:

eARC Input Config
?
Select the default mode the Bijou outputs when a stereo signal is received on this input.

2 Channel Mode:
?
Select the default mode the Bijou outputs when a multi-channel signal is received on this input.

Multi-Channel Mode:
?
Adjust the output power level when using eARC.

Gain:
?
Dynamic Range Compression (DRC) reduces the volume of loud sounds, and amplifies quiet sounds.

DRC:

Digital Input Config
?
Turns the unit on from standby and switches to this input when audio is detected on this channel.

Signal Sense:
2 Channel Mode:
Multi-Channel Mode:

Gain:
DRC:
?
Set the volume output to max and disable volume control when using this input, allowing you to use variable volume control from the source.

Volume Defeat:

Analog Input Config

Signal Sense:
2 Channel Mode:

Gain:

Volume Defeat:

Dante Input Config

Signal Sense:
2 Channel Mode:

Volume Defeat:

Output Configuration

?
Output 1-2:
Output 3:
Output 4-5:
Output 6-7:
Sub Out:

Frequency Response

?
Output 1-2:
Output 3:
Output 4-5:
Output 6-7:
Crossover Frequency:

Output Gain
Test Tone:
Output 1:
Output 2:
Output 3:
Output 4:
Output 5:
Output 6:
Output 7:
Sub Out:

Speaker Distances
Units:
Output 1:
ft
in
Output 2:
ft
in
Output 3:
ft
in
Output 4:
ft
in
Output 5:
ft
in
Output 6:
ft
in
Output 7:
ft
in
Sub Out:
ft
in
Direct Mode:
Height Cue Filter:
Volume Leveler:
Loudness Management:
Dialog Normalization:
Surr Decoder:
Center Spreading:
Post Process:
DRC eARC Control:
DRC Digital Control:
DRC Cut:
Hz
DRC Boost:
Hz
Virtualizer:
Virtualization Front Angle:
Hz
Virtualization Surround Angle:
Hz
Virtualization Height Angle:
Hz
Virtualization Rear Surround Angle:
Hz
Profile:
2nd Stage Bass Mgmt:
HF Boost 4dB/oct:

Device Information
Host Name:
MAC Address:

Settings
DHCP:
IP Address:
Subnet Mask:
Default Gateway:
TCP Port:

Dante Settings
Dante DHCP:
Dante IP Address:
Dante Subnet Mask:
Dante Default Gateway:
NOTICE: EQ Disabled
?
Apply the EQ curve to each output, or disable the EQ off.

EQ Enable:

Output 1-2
Bass:
80 Hz:
150 Hz:
300 Hz:
700 Hz:
2500 Hz:
12000 Hz:
Treble:

Output 3
Bass:
80 Hz:
150 Hz:
300 Hz:
700 Hz:
2500 Hz:
12000 Hz:
Treble:

Output 4-5
Bass:
80 Hz:
150 Hz:
300 Hz:
700 Hz:
2500 Hz:
12000 Hz:
Treble:

Output 6-7
Bass:
80 Hz:
150 Hz:
300 Hz:
700 Hz:
2500 Hz:
12000 Hz:
Treble:

Subwoofer
31 Hz
40 Hz:
50 Hz:
63 Hz:
80 Hz:
100 Hz:

Treble

Enable:
Center Frequency:
Gain:

Low Pass Filter

Enable:
Frequency:
Q: